Preface Official Specs Versions Price Short Review Long Review What's Included Manual and Packaging Build Quality and Durability Size Retention Power User Interface and Operation Modes LED and beam Tint vs... Beamshots, Runtime, etc table. Comparisons Conclusion What I like What I don't like Up Next Notes
Sofirn is continuing their media blitz, and I’m on the receiving end! This time it’s the SF36, an 18650 medium-thrower.
This light only comes in one configuration, but there are two packages. One is just the light, and the other is a kit, which includes a cell and a charger.
The package with just the light is $18.99. The kit is $23.99. Both are available directly from Sofirn, on amazon.
At $19, I’d be flat wrong to say this light isn’t a good value. There are some things I’d like to improve (namely the switch), but it’s a nice (enough for $19) light!
This is the contents of the kit.
- Sofirn SF36 Tactical Flashlight
- Sofirn 2800mAh 18650
- Spare o-rings (2)
- Single bay charger
- Charger cable
Package and Manual
The light ships in a simple cardboard box. The light is in a plastic tray.
I like pictures in my manuals, but really, this manual is fine without. Overall the manual is good, and comprehensive.
Build Quality and Disassembly
The build quality of this Sofirn is on par with Convoy lights. It’s of a suitable quality for a $19 light. The knurling is great, the anodizing is good, and the reflector is well finished.
The head has large fins to help with cooling, but to be honest, heat didn’t seem to be an issue with the light anyway.
The head and tail separate from the body. The body is not reversible, and has a large spot for the friction clip, on the tail end.
The threads are triangle cut and anodized. The bezel unscrews easily and the lens is removable, but the reflector does not just fall right out.
Both the driver and switch are held in by brass retaining rings. The spring used here (both ends) is a thick single spring.
Officially 132 mm x 32mm x 25 mm.
Of course it’s longer than the Convoy S2+, but it’s also just a little larger in diameter, too.
The tailcap has a couple of holes on either side as lanyard attachment points. These work well, and still allow the light to tailstand easily.
There’s also a pocket clip, which ships installed. The clip is very grippy, but the touch point near the mouth is directly over some knurling. It could easily tear pants or whatever you clip to.
Also while this looks like one of those horrible cheap terrible clips, it’s actually not. It’s actually nice and thick, and has broken edges (ie not sharp).
The SF36 is powered by a single 18650, which is included with the kit. It’s rated at 2800mAh.
It’s a button top cell, with no mention of protection.
I tested this cell on my SkyRC MC300, and measured 2727mAh through the cycle test.
This light will not work with any configuration of multiple cells!
Here’s a runtime on High (the highest mode; no turbo!). This is of course with the included cell. Temperature is bouncing just due to house fluctuations.
Output is moderately stable for a few minutes, before dropping off to the next mode down. After that point, the profile is exactly like the “Medium” profile. I reset the light to High late in the run, but note that it doesn’t reach initial output.
Here is Medium. Stable across the runtime, at around 250 lumens. (Not sure what happened with the temperature at the end of this run. Regardless, the light was never hot anyway.)
The kit also includes a charger and a charging cable.
It’s a fine Li-Ion-only charger. I didn’t test this iteration, because I’ve already tested the charger when I reviewed the C8F. I found it to be a fine, simple charger.
User Interface and Operation
There’s just one switch on the SF36, a mechanical tail reverse clicky.
The switch is really the only thing I don’t care for about the light. And the problem is more likely with the driver… There’s this weird pause on the reverse of the reverse clicky. Not a natural pause. There’s a split second where you know the light should be switching modes, and it’s not, and then it does. It’s annoying, and puts me off. But I don’t think it’s a deal breaker.
Here’s a UI table!
|Off||Click||On (mode memory except Strobe)|
|On||Half Click||Mode cycle (L>H direction)|
|On||Double Half Click||Strobe|
|Strobe||Half Click||Previous Regular Mode|
|Mode||Mode Claimed Output (lm)||Claimed Runtime||Measured Lumens||Tailcap Amps|
LED and Beam
The emitter of choice is a Cree XP-L HD, V6. The reflector is smooth, but not perfectly smooth. It does make for a tight beam, though I measured it at only 144m throw.
Tint vs BLF-348
I have to say, the tint on this one is quite nice. And if I disregard the overexposed hotspot above, this is probably the closest I can recall a light matching the BLF-348.
Beamshots, Runtime, and Lux Measurements
|Glamour Shots||Beamshots [0.3″, f/8, ISO 100, 5000k]|
|Claimed Lumens (lm)||1070|
|Lux (Measured)||179 lux @ 5.387 m|
|Candela (Calculated) in cd||5194.5|
|Throw (Calculated) (m)||144.1|
|Throw (Claimed) (m)||200|
There are many other lights like this one. But at this price, in Neutral White…. this is a great deal.
What I like
- Low price, even for the kit.
- Tint is very good
- Built quality is good enough for the price
What I don’t like
- Annoying pause on the reverse clicky.
I have a knife to review tomorrow, and hopefully 2 more lights this week!
- This light was provided by Sofirn for review. I was not paid to write this review.
- This content originally appeared at zeroair.wordpress.com. Please visit there for the best experience!
- Whether or not I have a coupon for this light, I do have a bunch of coupons!! Have a look at my spreadsheet for those coupons. It’s possible to subscribe and get notifications when the sheet is edited!!